Furnaces can last a fair few years, provided you take proper care of them. That means scheduling preventive maintenance at least once a year, but it also means calling for repairs as soon as you suspect that something is wrong with the system. Even seemingly minor issues can actually cause serious damage in some cases, so it’s never a good idea to ignore a problem once it presents itself. Let’s take a look at some of the more dire furnace issues, and how to identify them.
Carney All Seasons Blog: Posts Tagged ‘Furnace Replacement’
Problems That can Lead to Furnace ReplacementMonday, February 20th, 2017
Signs You Need a New FurnaceMonday, November 7th, 2016
The coldest part of the year is not far off at all, which means strain on your heating system is going to be at its most severe before too long. If your furnace is unable to keep your home warm through another winter, it’s best that you replace it now. You don’t want it breaking down on you in the middle of the coldest month of the year, do you? Let’s take a look at some of the signs that you need a new furnace.
Signs That Your Furnace Needs ReplacingMonday, January 4th, 2016
Furnaces can last quite a while, as long as they’re properly taken care of. However, every furnace will eventually reach the end of its life. If your furnace is getting ready to permanently break down, you need to be able to recognize the signs. You don’t want to have your system suddenly die on you in the middle of a cold day, after all. So, keep an eye out for the following signs that you need a new furnace.
Heating Installation Guide: System Ventilation 101Monday, January 30th, 2012
Maintaining Proper Ventilation for Combustion Systems
Anytime you maintain, retrofit, or replace a gas heating system in your Buckingham home you also need to be concerned with air quality. Combustion air is needed by all oil and gas heating systems to support the combustion process. This air is provided in some homes by unintentional air leaks, or by air ducts that connect to the outdoors. The combustion process creates several byproducts that are potentially hazardous to human health and can cause deterioration in your home. You can protect yourself from these hazards, as well as maintain energy efficiency, by ensuring that your chimney system functions properly and that your gas heating system is properly ventilated. In some cases, installing a sealed-combustion furnace can also help.
Properly functioning chimney systems will carry combustion byproducts out of the home. Therefore, chimney problems put you at risk of having these byproducts, such as carbon monoxide, spill into your home.
Most older gas furnaces have naturally drafting chimneys. The combustion gases exit the home through the chimney using only their buoyancy combined with the chimney’s height. Naturally drafting chimneys often have problems exhausting the combustion gases because of chimney blockage, wind or pressures inside the home that overcome the buoyancy of the gases.
Atmospheric, open-combustion furnaces, as well as fan-assisted furnaces, should be vented into masonry chimneys, metal double-wall chimneys, or another type of manufactured chimney. Masonry chimneys should have a fireclay, masonry liner or a retrofitted metal flue liner.
Many older chimneys have deteriorated liners or no liners at all and must be relined during furnace replacement. A chimney should be relined when any of the following changes are made to the combustion heating system:
When you replace an older furnace with a newer one that has an AFUE of 80% or more. These mid-efficiency appliances have a greater risk of depositing acidic condensation droplets in chimneys, and the chimneys must be prepared to handle this corrosive threat. The new chimney liner should be sized to accommodate both the new heating appliance and the combustion water heater by the installer.
When you replace an older furnace with a new 90+ AFUE appliance or a heat pump. In this case, the heating appliance will no longer vent into the old chimney, and the combustion water heater will now vent through an oversized chimney. This oversized chimney can lead to condensation and inadequate draft. The new chimney liner should be sized for the water heater alone, or the water heater in some cases can be vented directly through the wall.
Other Ventilation Concerns
Some fan-assisted, non-condensing furnaces, installed between 1987 and 1993, may be vented horizontally through high-temperature plastic vent pipe (not PVC pipe, which is safely used in condensing furnaces). This type of venting has been recalled and should be replaced by stainless steel vent pipe. If horizontal venting was used, an additional draft-inducing fan may be needed near the vent outlet to create adequate draft. Floor furnaces may have special venting problems because their vent connector exits the furnace close to the floor and may travel 10 to 30 feet before reaching a chimney. Check to see if this type of venting or the floor furnace itself needs replacement. If you smell gases, you have a venting problem that could affect your health. Contact your local utility or Buckingham heating contractor to have this venting problem repaired immediately.
Chimneys can be expensive to repair, and may help justify installing new heating equipment that won’t use the existing chimney.
Heating Guide: High Efficiency Furnaces and Chimney ConcernsWednesday, December 14th, 2011
When upgrading to a high efficiency gas furnace in Telford, you may need to make some upgrades to your chimney. Older chimneys built for standard furnaces with normal exhaust needs are not built to the specifications needed by today’s high efficiency models. Not only is it unsafe to leave it as is, but the cost of repairs if you don’t have it upgraded can be substantial.
A common concern when upgrading to a high efficiency gas furnace is the issue of condensation and draft. Because the amount of exhaust being vented is reduced by a high efficiency furnace, your current setup is not sufficient for the new model. So, it needs to be reduced in size by a professional to avoid backup of exhaust. Proper chimney sizing is a complex process that requires professional guidelines and careful measurements of all appliances in your home.
Because the chimney often isn’t used at all for a high efficiency furnace (often PVC pipe used instead), the extra airflow in the chimney can become a major issue.
The biggest concern for the chimney when changing the furnace efficiency is condensation. Specifically, acidic condensation droplets can build up in the chimney if not properly stopped. A new chimney liner must be placed in the chimney to avoid excessive corrosion due to the acid droplets. Keep in mind that the efficiency of your new furnace will determine whether you will use the traditional chimney for exhaust or if a new line will be installed to vent your furnace.
When to Take Action
If you have your furnace replaced, your technician will likely discuss the chimney situation in your home with you. Keep in mind that this might be necessary and that there might be an added cost involved because of it. Modern furnaces are not designed to accommodate aging chimneys and your safety and the integrity of your house are at risk if you don’t retrofit the chimney if necessary.