Carney All Seasons Blog: Archive for the ‘Heating’ Category

Why is My Furnace Turning On and Off?

Friday, November 18th, 2011

One of the most annoying things your furnace can do is to constantly keep turning on and off. This on-off cycling keeps your Yardley home from heating up properly. This action – called short cycling – also requires more electricity and drives up utility bills.

Short cycling is caused by an overheated furnace, which triggers safety mechanisms and shuts down the furnace. After a brief interval and cooling down, the furnace starts up again the cycle keeps repeating itself. Not only is it an annoyance, it can also signal more serious problems. A leaking heat exchanger can cause a furnace to overheat – and produce deadly carbon monoxide gas.

If a furnace is working too hard and overheating, it is usually because of airflow in and out. Your home’s ventilation system needs to be clear of dirt, dust, and debris. The more blockage in your ductwork and vents, the more friction is created, slowing down airflow and ultimately ending with an overworked furnace that continues to cycle on and off. And a blocked exhaust vent, such as a chimney or dedicated exhaust vent, can also cause a furnace to work harder. Check for things like leaves or bird’s nests.

The blockage may also be coming from a clogged furnace filter. You should clean or replace your furnace filter after a visual inspection reveals any type of build-up of dust or dirt. Do this at least every three-six months.

If you have a two-speed fan on your furnace, it is recommended that you run the fan in low speed during the cold months and high speed in the warm months. The reason? Warm air is lighter and takes less force to move.

There are other measures to take to prevent short cycling but these usually require a professional heating and cooling service technician to correct the problem. If in doubt, call your local qualified heating and cooling contractor and schedule a furnace inspection. Don’t make your furnace work any harder than it was designed for – and keep your home’s occupants comfortable and safe.

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on Why is My Furnace Turning On and Off?

Make Your Heating System More Energy Efficient

Wednesday, November 16th, 2011

Efficiency is what you want when it comes to heating your Abington home. You want a furnace that provides the greatest degree of accurate indoor comfort while at the same time operating at peak efficiency to reduce energy usage and lower utility bills. That’s seems like a lot to ask of a simple mechanical system but you should expect it out of the furnace in your basement, attic, or mechanical room.

It is especially important today as energy costs have steadily increased, including electricity, natural and propane gas, and oil. The best way to combat rising prices is to have a furnace that uses less energy. It is a simple statement but one that bears repeating: higher efficiency equals lower operating costs.

Here are some ways to make your heating system more energy efficient:

  1. Clean or replace furnace filters on a regular basis. A dirty or clogged filter will make your furnace work harder and become much less energy efficient. Monthly or quarterly cleaning or replacements are easy to do and will result greater operating efficiencies.
  2. Inspect your home’s ventilation system for accumulation of dirt, dust, or debris. Have you recently added new carpeting? Do your pets shed? Is there a large number of people living in your home? If you answered yes to any of these questions you may need to inspect your ventilation system.
  3. Remove obstructions from around vents and grilles. You need a clean path for air to flow into and out of rooms. Restricted airflow makes your furnace work harder and become less energy efficient.
  4. Consider an upgrade to a two-speed or variable speed furnace. Most older furnaces operated on one speed, which cycled on and off and consumed a lot of energy. Today’s furnaces operate at lower speeds, consuming less energy and often remaining on to keep a steady airflow and prevent constant on and off cycling. These newer furnaces are much more energy efficient and cost less to operate.
  5. Adhere to a regular schedule of planned furnace maintenance. If you don’t clean and inspect your furnace on a regular basis, schedule service calls with a local qualified heating contractor. Your contractor will likely have a service agreement plan to fit your budget, which allows for annual inspections, priority emergency service calls, and discounts on parts and services.

Besides saving on energy costs, your efficient furnace will leave a smaller “carbon footprint.” Your efficient furnace will exhaust less carbon dioxide into the atmosphere and maintain a more “green” profile. And being ecologically friendly can be just as important as saving money.

You can be assured that an energy efficient heating system will keep more money in your pocket this fall and winter.

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on Make Your Heating System More Energy Efficient

The Hardest HVAC Maintenance: Some Pointers from Sellersville

Monday, November 14th, 2011

Do you hate to work on your own mechanical equipment in your Sellersville home, like furnaces and plumbing fixtures? You aren’t alone. Many people are not cut out to be do-it-yourselfers (DIYers). They prefer to hand off their maintenance and repair chores to qualified professional. That’s not a bad thing. But there are lots of DIYers who prefer to work on their own home repairs – and those are the people who aren’t afraid to take on the most challenging jobs.

If you are looking for good ideas on how to maintain your home’s heating and cooling (HVAC) system beyond the normal filter changeouts, here are some good things to check – things that will help with the overall performance of your HVAC system.

  1. Check the ventilation system. The ventilation carries conditioned air from a main source throughout your home.  It takes a little time and effort to check your ventilation system for things like cracks or leaks around joints, but it is an important maintenance task. You may even find separations between joints or holes caused by nails. A leaky ventilation system could be sending conditioned air into attics, walls, or crawlspaces and making your furnace work extra hard just to keep your living areas warm and comfortable. Take time to visually inspect as much of your ventilation system as possible – usually metal or flex duct – and repair using joint glue, metal filler, or duct tape.
  2. Inspect the insulation. Your heating system works in conjunction with the insulation in your home to provide comfort and warmth while saving you on high utility bills. A home that is poorly insulated or not insulated at all will cause a furnace to work harder and not only send utility bills higher, but increase the possibility of mechanical failure. Replacing or adding insulation in walls and crawlspaces is a relatively easy, yet time-consuming task. You can roll down or tack up fiber insulation or blow in insulation into walls. You can also seal up cracks on your home’s walls, roof, or foundation with a number of different products. Once again, your goal is to make your heating system work less and save you money.
  3. Check the visible components of the furnace. A build-up of dust and dirt can make the moving components of your furnace work even harder, such as the motors, fan belts, contactors, etc. If you live in an area where there is lots of dust and humidity or if your home has several occupants and/or animals, it is particularly important to check your system on a regular basis. This can be done by removing the access panels and taking a vacuum cleaner hose into as many areas as possible. A good, thorough vacuuming should produce immediate results and make your furnace run much more efficiently.

Try these three steps and you may not have to repeat them for another year or so – possibly not ever again while you live in your home.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on The Hardest HVAC Maintenance: Some Pointers from Sellersville

Five Important HVAC Maintenance Tips

Friday, November 11th, 2011

Do you have a “mental checklist” of chores that need to be done a regular basis around your Solebury home, such as cleaning the window treatments, washing windows, shampooing rugs, etc.? There are various areas of your home that need regular maintenance and cleaning – and that list includes your heating and cooling (HVAC) equipment. Do you know a poorly operating furnace can cost you in increased energy usage and higher utility bills? That same poorly operating furnace can be discharging harmful carbon monoxide gas into your home, creating a health risk.

So, it is important to keep your furnace in peak operating condition and the best way to do that is by making a checklist of HVAC maintenance tasks. Let’s look at five of them.

  1. Check your filters. Routine replacement of your furnace filters should be every 1-3 months, depending on the indoor air quality of your home, number of occupants, size, etc. You can purchase disposable filters online, at a local “big box’ retailer, or from your local HVAC contractor. A visual inspection of your filter is the best way to determine if it needs replacing. If you have a removable electronic filter, it should be cleaned every few months using soapy water and a hose. Any restrictions to air flow through the filters can lead to poor indoor air quality and will cause your furnace to work even harder to circulate warm air through your duct system.
  2. Clean and insect the blower assembly and motor. You can do this with a vacuum. Also check the fan belt to make sure it is not too loose or if it has any cracks or splits.
  3. Look for any obstructions in vents and returns. Believe it or not, your furnace needs “help” to operate. Any build-up of dirt or debris around the grilles of your ventilation system will just make your furnace work a lot harder. Do a visual check inside and outside and pay special attention to flues and chimneys, where indoor air is exhausted. Any blockage can result in an accumulation of poisonous carbon monoxide gas.
  4. Keep the area clean and clear around your furnace and water heater. Never store flammable liquids near your heating equipment. Your furnace room is not a storage closet.
  5. Revisit your home’s insulation. When was the last time you checked out the insulation in your attic or crawlspace? Is it securely in place or drooping down? Are there bald spots where the insulation has deteriorated? Is the insulation sufficient or should it be upgrade?

Tips 1 and 2 relate directly to furnace maintenance but tips 3 to 5 are equally important, having a direct bearing on how your furnace performs and its ultimate efficiency. If you follow all five tips and have an annual inspection from a qualified HVAC contractor, you should enjoy a fall season of comfort, warmth, and safety.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on Five Important HVAC Maintenance Tips

How Often Should I Replace My Furnace Filter?

Wednesday, November 9th, 2011

Just like the filter in your air conditioner, replacing your furnace filter is the key to a healthy and comfortable Willow Grove home. By keeping a good filter replacement schedule, you will reduce wear and tear to the furnace and keep your home warm, while keeping your family healthy and controlling energy costs all winter.

But when does your furnace filter need to be changed? Well, each system is different, but there are some general guidelines and recommendations to follow that can help you keep it all straight and stay on top of your furnace filter situation.

Conventional Wisdom

The long-standing rule of thumb on furnace filters is to change them every month. This is good practice if you are using older fiberglass filters, but for newer, more efficient filters, you should do it a little differently. These should be inspected and cleaned at least once a month, but you may need to replace them that frequently also.

Sometimes it is a little more complicated than these general guidelines, so it pays to be aware of some factors and conditions in your home that may affect how frequently you need to change your filter.

Things to Consider

As mentioned above, the first thing to consider is the efficiency of the filter. Because new filters are so efficient, when they get dirty or clogged with dust and debris, they actually restrict airflow, making your furnace bog down and work harder. So, it is important to stay on top of a monthly inspection and cleaning schedule with these filters.

Also take into account air quality and sources of allergens both inside and outside your home. If you live in an area with a lot of pollutants in the air, you’ll want to replace your filters often to keep those out of your home. If you own a lot of pets, the dander and hair will wind up in your furnace filter and you may have to replace it more often.

Complicated enough for you? It doesn’t have to be. Simplify the whole process by doing the following: check your filter monthly and be prepared to change it that often, clean high-efficiency filters regularly, replace the filter at least every three months and again at the start of heating season.

If you do those things at a minimum, you will be in pretty good shape. If have any questions about furnace maintenance, contact your local contractor.

Continue Reading

Tags: , , , , , , ,
Posted in Heating | Comments Off on How Often Should I Replace My Furnace Filter?

My Furnace isn’t Producing Enough Heat

Friday, November 4th, 2011

If your Telford home is cold, many blame the furnace for not bringing up the warm temperatures or they blame the thermostat for not working right.

It may very well be a thermostat issue – often caused by the location of the thermostat – that is causing the problem. However, sometimes root cause is found in the furnace or ventilation system.

Your indoor environment may be contributing to a seemingly slow-moving furnace. Your furnace may be working too hard to keep up with the heat demand because of an excessive build-up of dirt or debris on the filter or around the moving parts, such as the motor or fan belt. The most obvious thing to do is to keep the airflow unobstructed and keep all working parts clean.

First of all, you should regularly check your furnace filters and if they are dirty, replace them or clean them. Disposable furnace filters are relatively inexpensive and come in a variety of sizes and media ratings (ratings determine what size media is used and its ability to trap certain sized particulate). You can buy these individually or in bulk from a number of different resources. It is a good idea to replace the filters every three-six months.

Mesh filters can be removed, cleaned and reinserted. Like replaceable filters, mesh filters should be checked on a regular basis and then cleaned at least every three months.

You can remove the access panels to your furnace and inspect the components for any build-up of dust, dirt, or debris. Using a vacuum with an extension hose usually is all it takes to clean up the area.

Other reasons for poor heating performance include dirty or blocked ductwork. The harder your furnace has to work to push air through the ventilation system, the longer it takes to bring the heat up. Make your furnace work less and keep vents clear and ductwork clean.

Finally, the reason your furnace isn’t producing enough heat may not be the fault of your furnace at all – you may have a leaky house. But that’s a whole different story.

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on My Furnace isn’t Producing Enough Heat

Is Your Furnace Making too Much Noise?

Wednesday, November 2nd, 2011

The old saying that “It is better to be seen than heard” certainly applies to the mechanical equipment in your Ambler home. If you hear a squeaky noise or loud clattering you automatically suspect that something is wrong. And if that noise is coming from your furnace, you better pay attention to it. A noise is an obvious sign of a problem – minor or major – and it could result in mechanical failure that could leave your home cold and uncomfortable – and affect your home’s indoor air quality.

Today’s newer variable-speed furnaces keep a constant airflow through the ventilation system utilizing a low speed fan that consumes small amounts of electricity. Constant airflow brings in fresh air and keeps the room air from becoming stale or stagnant. Because of this constant operation, it is important to ensure the furnace is running at peak efficiency, which also means that it is running quietly.

Here are some common noises, possible reasons, and suggested repairs. As always, if you are in doubt about how to repair your furnace, call a local qualified heating contractor and schedule a service call.

  • Squealing noise – could be a worn out or slipping blower belt. Check for proper tension of the belt or replace the belt if it is worn out or cracked.
  • Squealing noise – could be worn out motor shaft bearings. Lubricate the blower motor at the proper points.
  • Rumbling noise – often caused by a poorly adjusted pilot light when the burners are turned off. Adjust the pilot as necessary.
  • Rumbling noise – often caused by dirty gas burners when the burners are switched on. This problem requires service from a qualified heating technician.
  • Buzzing noise – often caused when a blower motor mounting come loose. Tighten the mounting screws or use shims to fill gaps.
  • Hissing noise – indicates a possible air leak. This problem requires service from a qualified heating technician.
  • Ticking noise – possibly a leaky gas valve. This problem requires service from a qualified heating technician.
  • Rattling noise – could be a dirty fan blade. Wipe the fan blade or clean with degreaser.
  • Rattling, grinding, or whining – could be resistance to airflow that causes the motor to work harder. Check the vents in each room for dirt, debris, or obstructions and clear them.
  • Vibrating noise – may not be the furnace but loose or cracked seams in the ventilation system. Check the ductwork seams and hangers to ensure everything is tight. You may need duct tape or bracket hardware.

The best way to keep your furnace and ventilation system from making noises is to practice preventative maintenance. Have your furnace checked annually by a qualified heating contractor – and enjoy the peace and quiet.

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on Is Your Furnace Making too Much Noise?

It’s Time for Fall Maintenance (and Happy Halloween Weekend!)

Friday, October 28th, 2011

Everyone at Carney Plumbing, Heating & Cooling wishes you a Happy Halloween weekend! We hope you have a great time dressing up and eating lots of candy! And after Halloween we all know it starts to get pretty cold, so it is time to start thinking about fall maintenance for your HVAC system.

When it comes to heating equipment maintenance and repairs, it does not pay to procrastinate. The longer you put off the maintenance, the higher the probability that your heating system will break down or your heating and cooling contractor will be unable to make an emergency repair when you need it. That’s why fall is the best time of the year to have maintenance and repair procedures performed.

Consider this: when do most people call a heating and cooling contractor? The answer: when they need a repair. The call could come in the middle of the night when a furnace stops working or during a family party on a weekend – both times when it is hard to find someone to do the repair work. Has this happened to you? If so, there are ways you could have prevented this from happening – and could have saved from cold nights and embarrassing situations with house guests.

You can avoid this aggravation and extra expense by scheduling fall maintenance for your heating system. Fall is often the “slow season” for heating and cooling professionals and many schedule their routine service and maintenance appointments during this time. Contractors expect to be busy during the peak winter months and prefer to spread out the workload as evenly as possible.

During fall maintenance, your heating equipment will be switched on and inspected. That may sound routine but by running your heating system early, you may be spared the expense of repairing your system when it fails to operate or run smoothly during the cold months. If there is a problem, it is better to fix it ahead of time.

There is no guarantee that a furnace that is tuned up in the fall will last throughout the winter without needing service. But a little preventive maintenance ahead of time will save a lot of heartache – and dollars – when a real emergency comes up.

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on It’s Time for Fall Maintenance (and Happy Halloween Weekend!)

Things to Look for When Buying a Heating System

Friday, October 21st, 2011

If you are in the market for a new or replacement heating system in Abington and don’t know much about heating systems, you are not alone. Many homeowners are in the same boat as you. And many of that number put their trust in their local, professional, and qualified heating and cooling contractor to find the right furnace for their homes.

Before calling for an estimate, there are some things you can do to “prepare” yourself for one of the most important purchase you can make. Here is a checklist of things you should look for when buying a heating system.

Know your energy alternatives. There are lots of options today when it comes to heating your home. Gone are the days when the choices were so cut and dried. Check with your heating and cooling contractor for suggestions.

  1. Know what size your furnace should be. Furnaces are not “one size fits all.” The size of the furnace is determined by its Btu (British thermal unit) rating. For example, a one-story ranch home on a crawl space requires less heating capacity than a two-story colonial with a basement, thus it would require a furnace with a smaller numbered Btu rating. A home with a great deal of heat loss through windows and doors may require various furnace sizes. And don’t forget about insulation. Insulation can affect the furnace size, too. Again, check with your heating and cooling contractor for recommendations.
  2. How much room do you need for your furnace? Some homes have mechanical rooms for furnaces and water heaters while others utilize attics, basements, or crawlspaces for furnaces. If you think you need a big furnace to heat a big home, think again. Furnace manufacturers have been downsizing their heating equipment for years, while maintaining the same heating capacities. One example are wall hung boilers, which utilize water and electric as heating sources and are installed on a wall, making the unit easy to locate and easy to service – while at the same time being off the floor and out of the way.
  3. Will your heating system be “plug and play?” New furnaces can take the place of the ones they are replacing by using the same space. But sometimes a replacement unit may need some altering to fit into an existing duct system. It is almost a given that a new plenum (the part attaching the furnace to the ductwork) will have to be fabricated. But the new furnace may also require some other modifications to an existing duct system. You should understand this ahead of time and be prepared to pay additional costs.
  4. A box is a box is a box. As a rule, most heating systems are made the same. In some cases, one furnace manufacturer may produce several different brand names. The best “brand” is the heating and cooling contractor who installs and services your heating equipment. Do your homework ahead of time and find a qualified and professional contractor. Ask friends and family for recommendations. This is may be the most important thing to look for when buying a heating system

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on Things to Look for When Buying a Heating System

How to Get My Furnace Ready for Winter

Wednesday, October 19th, 2011

Being cold in the winter is normal – as long as you are outside. But you shouldn’t be cold inside your New Britain home. If that happens, the first place to look to is your furnace, which may not be working correctly. Furnaces are like any other piece of mechanical equipment. They need to be maintained and serviced on a regular basis to ensure they are working at peak efficiency and warming your entire home at your desired comfort level.

The best time to get your furnace ready for winter is not during the cold winter months – it is before the winter season even begins. There are several way to get your furnace ready for winter and let’s explore some of them.

First of all, check and see when you last had your furnace serviced. If it has been over one year ago, you should schedule and maintenance inspection from your local qualified heating and cooling professional. And when you make that appointment, ask about service agreements and getting on a regular maintenance schedule. Most heating and cooling contractors offer service agreement plans which include furnace and air conditioning check-ups on an annual basis.

Okay, so you know who to call for maintenance but what can you do yourself? First of all, give your furnace a little “help” by checking the vents and returns throughout the house. Ensure that there are no obstructions or blockages such as rugs, clothing, furniture, etc. You need to have unobstructed paths for your heated and return air to flow. The more congested the path, the harder your furnace will have to work. And while you’re at it, make sure your vents are open or closed, depending on how much you use your rooms. For example, if you have an extra bedroom that doesn’t need to be heated, closed off the vent or close the damper in the ductwork. The heated air will be diverted to other parts of your home where it is needed.

You can also help the airflow by vacuuming the vent cover or removing it and vacuuming any of the ductwork that you can easily get to. For a more thorough job consider calling a qualified and professional duct cleaning contractor. Many heating and cooling contractors also offer duct cleaning service, too.

Another maintenance function that you can perform is cleaning or replacing the furnace filter. Depending on the size of your home and its air quality (occupants, pets, etc.), you may want to clean or replace your air filter every one to three months. A dirty filter can restrict airflow and can put contaminants like dirt and dust right back into your air system. If you don’t know how to replace your air filter, consult the furnace owner’s manual or go online to learn more. If your furnace uses an electrostatic air filter, it will need to be removed and cleaned, either by using a hose or with soapy water and a hose. Make sure you let it dry before re-installing it.

You may also want to inspect any electrical wires around your furnace to ensure none are broken or frayed. A visual inspection should be good enough.

Once you have done what you can, let your heating and cooling professional take over from there. They are licensed and trained to inspect your furnace and ensure that it is in peak operating condition. And do it today – while everyone else is waiting.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on How to Get My Furnace Ready for Winter